Minicom Advanced Systems Smart 4 Uživatelská příručka Strana 63
- Strana / 92
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
To enter Safe mode:
1. While powering up
SmartRack 116 IP
the back panel
of the unit
The device boots up i
n
2. Wait
until the unit finishes booting (
3. Determine
the IP address of the
whether or not
there is a DHCP server on the network. If there is, the DHCP ser
assigns an IP address to the
unit boots with the static IP address 192.168.2.155.
4.
Open Internet Explorer and type into the Address box:
(Do not start the address with
T
he Login page appears.
5. In User, type userna
m
(This usernam
e and pa
A menu appears.
5.2
Restoring Factory Defaults
You can restore all
SmartRack 116 IP
Troubleshooting
Restoring
SmartRack 116 IP
, press and hold down the
Go Local
of the unit
for three to four seconds.
n
Safe mode.
until the unit finishes booting (
one to two minutes).
the IP address of the
SmartRack 116 IP unit
. The IP address depends on
there is a DHCP server on the network. If there is, the DHCP ser
assigns an IP address to the
SmartRack 116 IP unit
. If there is no DHCP server, the
unit boots with the static IP address 192.168.2.155.
Open Internet Explorer and type into the Address box:
http://IP
address/config
(Do not start the address with
https.)
he Login page appears.
Figure 68 – Login Page
m
e admin , and in Password, type SAFEmode (
ca
e and pa
ssword works only in Safe mode.)
Figure 69 – Safe Mode Menu
Restoring Factory Defaults
SmartRack 116 IP
settings to their default values.
Troubleshooting
– Safe Mode
Restoring
Factory Defaults
User Guide | 63
Go Local
button on
. The IP address depends on
there is a DHCP server on the network. If there is, the DHCP ser
ver
. If there is no DHCP server, the
address/config
.
ca
se sensitive).
- SmartRack 116 IP 1
- User Guide 1
- Legal Notice 2
- About this Document 3
- Style Conventions 4
- Table of Contents 5
- User Guide 7
- Table of Figures 10
- User Guide 11
- 1 Introduction 12
- 1.2 Terminology 13
- 1.3 Compatibility 13
- 1.5 Technical Precautions 13
- 1.7 Trademarks 14
- 1.8 WEEE Compliance 14
- 1.6 Safety 14
- 2 Installation 15
- Installation 16
- System Components 16
- 16 16
- The SmartRack 116 IP Unit 17
- Pre-Installation Guidelines 18
- 18 18
- Replacing the Bracket 19
- Connecting 20
- User Guide 21
- 22 22
- 2.5 Connecting the System 23
- 2.6 Connecting to the Servers 23
- Connecting a RICC/ROC PS/2 24
- Connecting a RICC 25
- /ROC USB 25
- Connecting a RICC SUN 26
- User Guide 27
- 3 Configuring the Network 28
- Interface 29
- Configuring the Network 30
- 30 30
- User Guide 31
- 32 32
- 3.3.2 Configuring 33
- Adding a User 34
- Configuring User Settings 35
- User Guide 35
- Deleting User(s) 36
- Blocking a User 36
- Editing User 36
- Information 36
- Configuring the KVM Switch 37
- 38 38
- Installing 40
- Upgrading Firmware 40
- User Guide 41
- 3.9 Reloading a 42
- 44 44
- Conducting 45
- Conducting a Remote Session 46
- Starting a Remote Session 46
- 46 46
- 4.2 Sharing a Remote Session 47
- Exclusive 48
- Full Screen Mode 49
- Verifying 50
- 50 50
- Adjusting the Video 52
- Manually 53
- Adjusting Video Settings 53
- Managing Keyboard Sequences 54
- User Guide 55
- Recording a New Custom Key 56
- Editing a Key Sequence 56
- Synchronizing Mouse Pointers 57
- 58 58
- The USB Option 59
- Aligning the M 60
- Pointers 60
- Calibrating Mouse 61
- 5 Troubleshooting – Safe Mode 62
- Restoring Factory Defaults 63
- Restoring the Device Firmware 64
- Figure 73 – Upgrade Succeeded 65
- Operating 66
- Using the Keyboard Hotkeys 66
- 66 66
- 6.2.3 Configuring t 67
- Configuring Security Settings 69
- Operating the SmartR 70
- Using the OSD 70
- 70 70
- Configuring the Port 71
- Configuring the T 72
- Configuring the Users 73
- Settings 73
- 74 74
- OSD Functions 75
- Scanning 76
- Computers (F4) 76
- Tuning (F5) 76
- Moving the Label ( F6) 77
- 78 78
- Starting and C 80
- Software 80
- Verifying the V 81
- RICC/ROC Version 82
- Obtaining N 83
- Firmware 83
- Troubleshooting 84
- – Update Software 84
- 6.4.4 Electricity F 85
- 86 86
- 7 Technical Specifications 87
- Technical Specifications 88
- 88 88
- User Guide 89
- 9 SNMP Events Table 90
- SNMP Events Table 91
- User Guide 91
- 201204210 • 933213_EN 92
Související produkty a manuály pro Sítě Minicom Advanced Systems Smart 4
(92 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce